Keyless2Go TOY44D-PT Transponder Key, 4D-67 DOT

They worked for a 2008 toyota sienna

My son was able to code them. I don't know how and I'm not sure he does. 👀

I cut & programmed these keys, and now they unlock the doors & start the car. 2008 Toyota Sienna minivan.

Item as described

Llego muy rápido y con mucha calidad

Purchased for a 2008 Toyota Sienna, got them cut at a Local Hardware store. Programmed them myself from instructions found on the internet and they work great!! Make sure your OEM keys have the little “dot” on the blade as indicated in the advertisement. Sit in vehicle with doors closed insert & remove OEM key from ignition (5) five times, on the (5th) fifth time leave the OEM key in the ignition. Open and close driver’s door (6) six times, leave door closed on the (6th) time. Remove OEM key, the vehicle’s immobilizer light will now be “on/lit” continuously. Insert the newly cut key into the ignition the immobilizer light will blink for approximately (1) one minute then the immobilizer light will “turn off/go out”. Remove the newly cut key from the ignition. It is now programmed.

cut great worked perfectly

Product summary: 10/10 would recommend.Ordered this for my mother who wore out her original Toyota key. After being turned away by the big box stores as well as one of America's favorite neighborhood hardware store, I finally contacted a locksmith to have these cut. Then following a YouTube video to get the key programed, it saved about $80-$120 per programmed key at the dealerships. Yes opening and closing your door eight times seems comical, but it may save you oodles of cash in the long run.

Works well on 2010 Toyota Matrix with $15 programming device plugged into OBD port. Saved hundreds compared to dealers and programming people.

Trace cut at hardware store.Programmed with techstream no problem.Great value alternative to OEM

Cut keys I have access to program toolsimple good keys would buy again .

I had them cut at Ace Hardware first and then programmed them to our 08 Sienna. I used a YouTube video to remind me of the procedure. Both keys worked fine.

Took a chance on these since the key machine at Walmart was gonna charge me $46.99 to make one (and it claimed to be more accurate than a locksmith) LoL. When I got these, I went to Home Depot, but their machine can't read or cut these. So then I took it to Ace Hardware and they say they don't do it. (Not that they can't, but that they don't or won't) So I called a local locksmith and he cut it for $2. Good deal. When I got home, I used it to open the door and the trunk of the car and it opened up just fine. Then I got in the car and programmed it and it starts up the car. I'll be taking the other blank in tomorrow to get it cut too. Should work. Took the other one to cut and it works just fine. Both programmed and good to go for 2005 Toyota Corolla.

Worked for my 08 tundra

I bought this to replace a lost key for my 2006 Toyota Sienna. Going through a dealership would be much more expensive. Some local locksmiths were quoting a higher price for a replacement car key as well. Took it to Home Depot, got it cut, and then programmed it myself. Saved a bunch of money. The programming instructions I found online took a few tries to get it right. These are the ones that worked for me:1. Sit in your van with all doors closed. I opened and closed the door one time to 'clear' the system.2. Insert your original master key to key cylinder 5 times and leave it there ('in' and 'out' four times, just 'in' the fifth time).3. Open and close driver side door 6 times. Should be closed when you do the next step.4. Remove master key from key cylinder, and within 5 seconds insert your new cut transponder key. (NOTE: the original instructions I found said to then turn the new key to the ON position, but that didn't work for me. Someone suggested completing the steps without turning to ON and that worked for them, tried it and it worked for me too.)5. Look at that red engine immobilizer light (the red light to the left of the speedometer which is car shaped with a black key in the middle of it). It is solid indicating it's in programming mode. After inserting the new key it will begin blinking. Wait about 1 min up to 90 seconds and it will turn off by itself.6. After engine immobilizer light turns off, remove new key and insert original master key. Start engine.7. Now try your DIYed new transponder key to start your Sienna.Obviously different models or different years of Sienna the programming instructions may vary. And even doing the same steps it took a few tries before it worked for me. But hey, way cheaper to do it myself!

Programming is a bit prolonged, but they work fine

Great price, worked without issue.

I saved alot purchasing these keys and having them cut to match, then program my self, they did take a few tries to get them to program, but they work just like the original once programed for my 2005 sequoia

No problem

Perfe t

So after many attempts to program, I found the magical (non-orthodox) way of programming and the key worked. Who knew if you turn on data logging for the autel 200 programmer the programming would work, when otherwise it wouldn't? Doesn't make sense, but the key works now.

The keys don't look as nice as the OEM keys but so far they work well

Needed an extra key but refused to pay dealer cost. These worked just fine. After programming by a locksmith they were a real money saver.

Saved us a LOT of money! IF you read the description and get the right blanks.

As described

No issues was able to program and work

Works perfectly

Saved me a lot of time and money!!! Especially cuz I got it cut at the dealership.

Works great for my 2004 Sienna. Programming the key took me a couple of tries following the online step by step process. Doing this yourself can save you $$.

Programmed first, then had it cut - works great!

I got the keys copied at my Toyota dealer and then programmed the keys myself. Total cost for the cost of the keys and copying was less than $25. I recommend going to your local dealer/locksmith, ask them to copy the keys and then program it yourself. Programming is very easy, it takes a few minutes and you don't need any special tools. Watch YouTube tutorials for programming instructions.

Product works as it should. Programming was easy enough for my '04 Camry